Self Help Forums

Go Back   Self Help Forums > Repair > Heating & Air Conditioning - Existing Home
Register FAQ Members List Calendar Today's Posts

Heating & Air Conditioning - Existing Home Heating & Cooling / Repair , Additions & Problems Solving Solutions

Reply
 
Thread Tools Display Modes
  #1   IP: 71.251.61.249
Old November 7th, 2007, 03:18 PM
CR500's Avatar
CR500 CR500 is offline
Senior Member
 
Join Date: Feb 2006
Posts: 447
Default Carrier or Bryant

They're supposed to be the same, made in the same factory, ....

I picked out the components I want and a contractor buddy got me his pricing and there was only about $100 difference between brands.

Should I save the $100 or go for the bigger name?
Reply With Quote
  #2   IP: 149.32.254.242
Old November 7th, 2007, 04:45 PM
sloooo sloooo is offline
Senior Member with Distinction
 
Join Date: Oct 2006
Location: Redlands, California
Posts: 789
Default

I would go with Carrier. The are made at the same plant but engineered different. Carrier has a great reputation for engineering AC units.
Reply With Quote
  #3   IP: 192.5.27.138
Old November 8th, 2007, 03:43 AM
CR500's Avatar
CR500 CR500 is offline
Senior Member
 
Join Date: Feb 2006
Posts: 447
Default

Ok, I'll go for the Carrier stuff. This is what I picked out. There is only a difference of 1 SEER between the two condensing units. My buddy said there isn't much difference in his cost, so I'll go with the scroll compressor.

Rob

Bryant:
Gas Furnace
355AAV060100 94%, Variable Speed Fan, Two Stage Heat, 100k BTU

Condensing Unit
187ANA048000 Evolution 17, 4-ton, Puron, 2-stage Reciprocating

Condensing Unit
180ANA048001 Evolution 20, 4-ton, Puron, 2-stage Scroll

Evaporator Coil CNPVP4821ATA
N-coil, 4-ton, Puron, TXV, Cased, Tin Plated, Upflow

Thermostat
SYSTXBBUID01 Evolution Control, Latest Revision


Carrier
Gas Furnace 58MVB100F10020
Condensing Unit 24ANA748A003 Infinity 17, Reciprocating
Condensing Unit 24ANA148A003 Infinity 21, Scroll
Evaporator Coil CNPVP4821ATA
Thermostat SYSTXCCUID01 Infinity Control
Reply With Quote
  #4   IP: 149.32.254.242
Old November 8th, 2007, 05:58 AM
sloooo sloooo is offline
Senior Member with Distinction
 
Join Date: Oct 2006
Location: Redlands, California
Posts: 789
Default

Scroll is a little cheaper to operate, so you'll be saving money in the long run. Make sure the coil includes the TXV and not the orafice.
Reply With Quote
  #5   IP: 192.5.27.138
Old November 8th, 2007, 06:44 AM
CR500's Avatar
CR500 CR500 is offline
Senior Member
 
Join Date: Feb 2006
Posts: 447
Default

According to the info the TXV is already in the coil.

Now I just need to knock the hole in my block basement wall for the pipes. Wish it didn't have the requirement to be off to the sides of line projected up from the electrical meter. That pushes me too close to some windows so I'll have to go out a different wall.

My buddy was telling me that when I remove the existing furnace, I'll have to increase the pipe from the water heater from 3" to 4". Does that sound right?

Thanks!

Rob
Reply With Quote
  #6   IP: 149.32.254.242
Old November 8th, 2007, 07:38 AM
sloooo sloooo is offline
Senior Member with Distinction
 
Join Date: Oct 2006
Location: Redlands, California
Posts: 789
Default

if your increasing the BTU output of the heater, you'll need to go larger. Depending on the efficiency, you could have a PVC vent pipe.
Reply With Quote
  #7   IP: 192.5.27.138
Old November 8th, 2007, 08:04 AM
CR500's Avatar
CR500 CR500 is offline
Senior Member
 
Join Date: Feb 2006
Posts: 447
Default

This furnace will be vented via PVC. I guess the problem is removing the heat load of the old furnace vent and only leaving the water heat to vent through the large pipe.
Reply With Quote
  #8   IP: 149.32.254.242
Old November 8th, 2007, 10:00 AM
sloooo sloooo is offline
Senior Member with Distinction
 
Join Date: Oct 2006
Location: Redlands, California
Posts: 789
Default

Your going to have a water trap for the PVC that you'll need to run to a drain. Don't dump it on the ground. The combustion condensate is some nasty stuff and is unhealthful for plants and other little critters.
Reply With Quote
  #9   IP: 71.251.52.80
Old November 8th, 2007, 04:27 PM
CR500's Avatar
CR500 CR500 is offline
Senior Member
 
Join Date: Feb 2006
Posts: 447
Default

I need to read the installation directions again. I think they want the pipe pitched so the condensate runs back towards the furnace. I have a drain in the floor right next to the furnace where I have my dehumidifer empty into. Someday I'll have to figure out if its connected to the city sewer or if its something like a gravel pit.
Reply With Quote
Reply






Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 09:29 AM.


Powered by vBulletin® Version 3.6.7
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
© 2002 - QuinStreet, Inc.
http://www.selfhelpforums.com